This is a very nice micro servo. Its strength and speed vs weight is unparalleled by any other micro servo I've found. The output shaft is free to turn 360 degrees but the controller will only rotate it about +/- 50 degrees. I was hoping it would achieve +/- 90 to be used on a robot. I connected it to an Arduino and used the writeMicroseconds command to try out of range values and it still only turns +/- 50 degrees. I disassembled one to check the construction quality. All the gears are metal and there are two ball bearings supporting the output shaft. The potentiometer was 1800 ohms with a 2.5V reference voltage and over 180 deg of useable rotation. In theory this digital servo should be programmable to modify the angular limits but I couldn't find any documentation. There are 4 SOT23 transistors on the circuit board that appear to be a full discrete H-Bridge driving the motor. The control horns felt a little loose and the spline would occasionally slip if stalled. The midsection of the housing does appear to be made of some kind of metal. I was able to solvent weld a small piece of ABS to the bottom plate using acetone so the top and bottom plates are likely made of ABS. I really like this servo and would buy many more if there was a way to increase the rotation angle.

This is a very nice micro servo. Its strength and speed vs weight is unparalleled by any other micro servo I've found. The output shaft is free to turn 360 degrees but the controller will only rotate it about +/- 50 degrees. I was hoping it would achieve +/- 90 to be used on a robot. I connected it to an Arduino and used the writeMicroseconds command to try out of range values and it still only turns +/- 50 degrees. I disassembled one to check the construction quality. All the gears are metal and there are two ball bearings supporting the output shaft. The potentiometer was 1800 ohms with a 2.5V reference voltage and over 180 deg of useable rotation. In theory this digital servo should be programmable to modify the angular limits but I couldn't find any documentation. There are 4 SOT23 transistors on the circuit board that appear to be a full discrete H-Bridge driving the motor. The control horns felt a little loose and the spline would occasionally slip if stalled. The midsection of the housing does appear to be made of some kind of metal. I was able to solvent weld a small piece of ABS to the bottom plate using acetone so the top and bottom plates are likely made of ABS. I really like this servo and would buy many more if there was a way to increase the rotation angle.

This is a very nice micro servo. Its strength and speed vs weight is unparalleled by any other micro servo I've found. The output shaft is free to turn 360 degrees but the controller will only rotate it about +/- 50 degrees. I was hoping it would achieve +/- 90 to be used on a robot. I connected it to an Arduino and used the writeMicroseconds command to try out of range values and it still only turns +/- 50 degrees. I disassembled one to check the construction quality. All the gears are metal and there are two ball bearings supporting the output shaft. The potentiometer was 1800 ohms with a 2.5V reference voltage and over 180 deg of useable rotation. In theory this digital servo should be programmable to modify the angular limits but I couldn't find any documentation. There are 4 SOT23 transistors on the circuit board that appear to be a full discrete H-Bridge driving the motor. The control horns felt a little loose and the spline would occasionally slip if stalled. The midsection of the housing does appear to be made of some kind of metal. I was able to solvent weld a small piece of ABS to the bottom plate using acetone so the top and bottom plates are likely made of ABS. I really like this servo and would buy many more if there was a way to increase the rotation angle.

using them as cyclic servo and tail servo for copter x 250 . buy with confindence

using them as cyclic servo and tail servo for copter x 250 . buy with confindence

using them as cyclic servo and tail servo for copter x 250 . buy with confindence

Per il prezzo non si può ottenere niente di meglio!!!

For the price you can't get anything better!!!

Per il prezzo non si può ottenere niente di meglio!!!

Ho ordinato questi servi per i miei aeroplani schiumosi all'aperto. Il D0576HT pesa 8,2 g senza braccio servo e vite centrale misurata su una scala di grammo digitale. È elencato come 7,9 g ma ho provato a pesare 2 pezzi e ha ottenuto 8,2 g. Il servo viene fornito con un assortimento di bracci servo e sono rimasto piacevolmente sorpreso dal fatto che uno di essi fosse extra lungo. Ho usato per fare le estensioni fenoliche delle trombe come il D074 da Inservos non è venuto con il braccio servo lungo. Bel lavoro BlueArrow. L'ho alimentato con una batteria LiFe 6.6V per controllare se funzionava. Nessun problema. I miei primi risultati sono che il D0576HT è molto veloce, più veloce del D0474 e ben centrato.Le specifiche di coppia sono impressionanti e non vedo l'ora di installare questi servos nel mio aereo 3D.

I ordered these servos for my outdoor foamy airplanes. The D0576HT weighs 8.2 g without servo arm and center screw measured on a digital gram scale. It is listed as 7.9g but I tried weighing 2 pcs and got 8.2g. The servo comes with an assortment of servo arms and I was pleasantly surprised that one of them was extra long. Fit for a 3d foamy. I used to have to make phenolic horn extensions as the D074 from Inservos didn't come with the long servo arm. Nice job BlueArrow. I powered it up with a LiFe 6.6V battery to check if it was working. No problems. My initial findings are the D0576HT is very fast, faster than the D0474 and centered well. Torque specs are impressive and I can't wait to install these servos in my 3d plane.

Ho ordinato questi servi per i miei aeroplani schiumosi all'aperto. Il D0576HT pesa 8,2 g senza braccio servo e vite centrale misurata su una scala di grammo digitale. È elencato come 7,9 g ma ho provato a pesare 2 pezzi e ha ottenuto 8,2 g. Il servo viene fornito con un assortimento di bracci servo e sono rimasto piacevolmente sorpreso dal fatto che uno di essi fosse extra lungo. Ho usato per fare le estensioni fenoliche delle trombe come il D074 da Inservos non è venuto con il braccio servo lungo. Bel lavoro BlueArrow. L'ho alimentato con una batteria LiFe 6.6V per controllare se funzionava. Nessun problema. I miei primi risultati sono che il D0576HT è molto veloce, più veloce del D0474 e ben centrato.Le specifiche di coppia sono impressionanti e non vedo l'ora di installare questi servos nel mio aereo 3D.

Quei servi sono potenti, super veloci, super forti, ben fatti, hanno un po'di allentamento dopo un po', appena percettibili, suggerito

those servos are mighty ,super fast super strong,well made ,they have some slack after a while ,barely noticeable ,suggested

Quei servi sono potenti, super veloci, super forti, ben fatti, hanno un po'di allentamento dopo un po', appena percettibili, suggerito

non potrò mai comprare da banggood nuovo, consegna reale super, super lungo, im non davvero bather per testare se funziona perché ho già comprato da un altro modo negozio dopo aver ordinato questo ed è venuto modo prima

i will never buy from banggood again, delivery real super, super long, im not really bather to test if it works because i already bought it from another store way after i order this and it came way before

non potrò mai comprare da banggood nuovo, consegna reale super, super lungo, im non davvero bather per testare se funziona perché ho già comprato da un altro modo negozio dopo aver ordinato questo ed è venuto modo prima

Eccellente servo super preciso, centraggio perfetto e molta potenza

Excellent servo super precise, perfect centering and plenty of power

Eccellente servo super preciso, centraggio perfetto e molta potenza

ottimi servi

ottimi servi

ottimi servi

gute Qualität guter Preis

gute Qualität guter Preis

gute Qualität guter Preis

Kleine Abmessungen alles bestens und auch für den HV Betrieb.

Kleine Abmessungen alles bestens und auch für den HV Betrieb.

Kleine Abmessungen alles bestens und auch für den HV Betrieb.